d s 21313 rev. e-3 1 of 2 mp15005/w - mp1510/w mp15005/w - mp1510/w 15a bridge rectifier features mp-w c a g e b h (ac) (ac) (+) (-) h j a c k a m b h h l p a p (ac) (ac) (-) (+) mp mechanical data w suffix designates wire leads no suffix designates faston terminals mp / mp-w dim min max a 28.40 28.70 b 9.70 10.00 c 15.70 16.70 e 22.86 25.40 g 13.50 14.50 h hole for #10 screw 5.08 nominal j 17.50 18.50 k 10.90 11.90 l 0.97 1.07 m 30.50 ? p 17.60 18.60 all dimensions in mm diffused junction low reverse leakage current low power loss, high efficiency surge overload rating to 300a peak case to terminal isolation voltage 1500v ul listed: recognized component index, file number e95060 case: molded plastic with heatsink internally mounted in the bridge encapsulation terminals: plated leads solderable per mil-std-202, method 208 polarity: symbols marked on case mounting: through hole for #10 screw mounting torque: 8.0 inch-pounds maximum mp weight: 23 grams (approx.) mp-w weight: 17 grams (approx.) mounting position: any maximum ratings and electrical characteristics @ t a = 25 c unless otherwise specified single phase, 60hz, resistive or inductive load. for capacitive load, derate current by 20%. characteristic symbol mp15 005/w mp15 01/w mp15 02/w mp15 04/w mp15 06/w mp15 08/w mp15 10/w unit peak repetitive reverse voltage working peak reverse voltage dc blocking voltage v rrm v rwm v r 50 100 200 400 600 800 1000 v rms reverse voltage v r(rms) 35 70 140 280 420 560 700 v average rectified output current @ t c = 55 c i o 15 a non-repetitive peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method) i fsm 300 a forward voltage (per element) @ i f = 7.5a v f 1.1 v peak reverse current @ t c = 25 c at rated dc blocking voltage @ t c = 125 c i rm 10 0.5 a ma i 2 t rating for fusing (note 1) i 2 t 373 a 2 s typical junction capacitance (note 2) c j 200 pf typical thermal resistance junction to case (note 3) r jc 6.3 k/w operating and storage temperature range t j, t stg -65 to +125 c notes: 1. non-repetitive, for t > 1.0ms and t < 8.3ms. 2. measured at 1.0mhz and applied reverse voltage of 4.0v dc. 3. thermal resistance junction to case per element mounted on heatsink.
d s 21313 rev. e-3 2 of 2 mp15005/w - mp1510/w 1.0 10 100 1000 0.2 0.6 1.0 1.4 1.8 2. 2 instantaneous forward voltage (v) fig. 2 typical forward characteristics inst ant ane o us f o r w ard current (a) 0 100 200 300 400 1.0 10 100 number of cycles at 60 hz fig. 3 maximum non-repetitive surge current peak f o r w ard surge current (a) single half-sine-wave jedec method 0.01 0.1 1.0 10 0 20 40 60 80 100 120 140 inst ant ane o us reverse current (a) percent of rated peak reverse voltage (%) fig. 4 typical reverse characteristics t = 25c j t = 125c j 0 5 10 20 25 15 25 50 75 100 125 i , a vera g er e c tified c urrent ( a ) o t , case temperature (c) fig. 1 forward current derating curve c resistive or inductive load
|